GDPR Compliance Page

Les conseils de l'atelier pour une installation parfaite !
L'application utilisée pour assurer la conformité de ce site au RGPD/CCPA-CPRA recueille votre adresse IP et votre adresse électronique afin de traiter les données. Pour en savoir plus, consultez la politique de confidentialité.

Data rectification

You can use the link below to update your account data if it is not accurate.

Data portability

You can use the links below to download all the data we store and use for a better experience in our shop.

Access to personal data

You can use the link below to request a report that will contain all the personal information we store for you.

Right to be forgotten

Use this option if you want to delete your personal data and others from our store. Keep in mind that this process will delete your account, so you will no longer be able to access or use it.

Preparation

1. Preparation of the material

Before starting, prepare the following items:

  • A clean, lint-free cloth
  • A degreasing cleaner (such as isopropyl alcohol, 70% or 90% IPA)
  • A soft squeegee or a plastic card wrapped in microfiber
  • A hairdryer or a heat gun (on low power)
  • Your stickers sorted by parts (fairing, mudguard, sides, etc.)

Make sure to work in a clean, dry, and dust-free area.

2. Preparation of the motorcycle or scooter

A perfect preparation ensures optimal adhesion.

  • Thoroughly wash the motorcycle to remove dirt.
  • Dry all the fairings.
  • Degrease all surfaces where the decal kit will be applied with isopropyl alcohol.
  • Pay special attention to:
    the sides,
    the airbox,
    the front and rear fenders,
    the side covers,
    the tank (if applicable).

No traces of grease, dust, or silicone should remain on the plastics.

Positioning

3. Dry positioning

Before permanently sticking:

  • Place each sticker in front of its location.
  • Check the orientation, markers, and curves.
  • Visually adjust the overall position.

A dry fit allows you to avoid mistakes once the adhesive is applied.

Application

4. Applying the decal kit

4.1 Peel and Position

  • Peel a small part of the liner (the white paper on the back).
  • Place the sticker on the fairing piece.
  • Stick one end first (usually the center or the straightest edge).

Don’t stick it all at once: work gradually.

4.2 Gradual Application and Squeegee

  • Proceed little by little, removing the liner as you go.
  • Use the squeegee or a card wrapped in a cloth to smooth the surface.
  • Push the air out from the center towards the edges.
  • If a bubble appears, peel back slightly then reapply.

Thanks to the FLO anti-bubble adhesive, air escapes easily.

4.3 Light Heating

Applying some heat softens the vinyl and helps it perfectly fit the shapes.

  • Gently heat with a hairdryer (never too hot).
  • Apply extra pressure on curved areas.
  • Don’t overheat: overheated vinyl becomes too soft and deforms.
Tips

6. Important Tips

  • Never apply a decal kit on a cold or damp surface.
  • Do not use silicone products before installation.
  • Avoid water during application (dry method recommended for FLO premium vinyls).
  • The cleaner the surface, the longer the adhesion will last.
  • If you make a mistake, peel off immediately and reposition; premium vinyl allows this.

Care for your decal kit

To extend the life of the vinyl:

  • Wash the bike by hand (avoid high-pressure washers too close).
  • Use gentle products, without harsh solvents.
  • For glitter or holographic finishes, prefer hand washing only.

Proper care ensures your decal kit stays vibrant for years.

Need help or advice?

Our team is available to assist you with applying your decal kit.

Whether it’s for an adjustment, a surface issue, or a question about installation, we respond quickly.