Pot Army SX 86 Top Alu AM6 Beta RR - Rieju MRT
The Army SX pot 86 top Alu, is specially designed and developed for motorcycles 50 cm3 Beta RR from 2011. The perfect combo with an 86 top alu cylinder kit. Discover the power of the 86 top alu kit with this custom-made exhaust to optimize the performance of the 86 top perf kit. Accelerations and pick-ups, this exhaust is very efficient whether at low or high speeds. If you are a fan of strong emotions, the Army SX 86 exhaust is made for you.
The SX 86 top alu is unique in its category, as it is 100% hand-made without any robot intervention. Even the part of the exhaust outlet, which represents a work with much more precision and time than a "standard" muffler. The muffler Army SX 86 is made up of 22 pieces of laser-cut steel sheets which are then welded one by one by hand. It takes more than 5 hours of work for each exhaust, not counting the time for cutting and assembly. Our exhausts are made in Spain by the best exhaust manufacturer in Europe. The SX 86 muffler comes with an Army Black aluminum silencer. The Army SX 86 exhaust can also be mounted on Rieju MRT and Sherco 50 cm3*
- Type of manufacture: 100% hand-welded rolled
- Material: 0.8mm sheet steel
Warning: product not homologated on the road, all-purpose on public roads is forbidden.
* Small modifications of the mounting arms are necessary in order to adapt it.
The Army SX pot 86 top Alu, is specially designed and developed for motorcycles 50 cm3 Beta RR from 2011. The perfect combo with an 86 top alu cylinder kit. Discover the power of the 86 top alu kit with this custom-made exhaust to optimize the performance of the 86 top perf kit. Accelerations and pick-ups, this exhaust is very efficient whether at low or high speeds. If you are a fan of strong emotions, the Army SX 86 exhaust is made for you.
The SX 86 top alu is unique in its category, as it is 100% hand-made without any robot intervention. Even the part of the exhaust outlet, which represents a work with much more precision and time than a "standard" muffler. The muffler Army SX 86 is made up of 22 pieces of laser-cut steel sheets which are then welded one by one by hand. It takes more than 5 hours of work for each exhaust, not counting the time for cutting and assembly. Our exhausts are made in Spain by the best exhaust manufacturer in Europe. The SX 86 muffler comes with an Army Black aluminum silencer. The Army SX 86 exhaust can also be mounted on Rieju MRT and Sherco 50 cm3*
- Type of manufacture: 100% hand-welded rolled
- Material: 0.8mm sheet steel
Warning: product not homologated on the road, all-purpose on public roads is forbidden.
* Small modifications of the mounting arms are necessary in order to adapt it.
Here are the steps to follow to install a 50cc motorcycle graphic kit:
Preparation: Make sure you have all the necessary materials, including the decorating kit, spatula, spray cleaner, cutter or razor blade, and hair dryer.
Cleaning: Carefully clean the areas where you want to install the deco kit. Be sure to remove all dirt, dust, grease, etc.
Trimming: If necessary, use a razor blade or craft knife to trim the edges.
Apply the first part: Slowly peel the backing from the first part of the deco kit and carefully place it on the fairing. Use a spatula to remove air bubbles and to firmly apply the vinyl.
Apply the other pieces: Continue to apply the other pieces of the decorative kit following the same steps as before. Make sure you align them correctly and place them carefully to avoid air bubbles.
Drying: Use a hair dryer to dry the vinyl and ensure optimal adhesion.
Finishing: Once all the pieces are in place, check that the deco kit is installed correctly. If necessary, use a craft knife or razor blade to trim the edges.
Note that every deco kit is different, so there may be variations in the steps mentioned above. Be sure to follow the instructions included with the deco kit for successful installation.
The manufacture of a motorcycle decoration kit includes several stages:
Validation of the customer model - The customer validates the design and colors of the decorative kit.
Printed on high quality vinyl - The design is printed on high quality vinyl to ensure excellent weather resistance and long-term durability.
Drying - The printed vinyl is left to dry to ensure good adhesion.
Hot Lamination of Protective Film - The printed vinyl is coated with a 450 micron protective film to protect the print from scratches and weather damage.
Precise cutouts - The cutout shapes are precise thanks to improved tools for a perfect fit on the motorcycle.
Quality Control- A quality inspection is carried out to ensure that the deco kit conforms to customer specifications and is free from defects.
Sending to the customer - The decorative kit is sent to the customer with tracking and SMS notifications.